GETTING FAMILIAR WITH PLUMBING: YOUR STARTING POINT FOR WHEN INSTALLING A BATHTUB

Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub

Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub

Blog Article

Check Us Out

Just how do you feel with regards to A Step-by-Step Guide to Installing a Bathtub?


Tools You Need to Install a New Bathtub
Installing a tub isn't precisely rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a new one is also a reasonably difficult task. If the old bathtub is easily accessible, the task can relocate rapidly; if you have to open up a wall to get rid of the old tub and place the brand-new bathtub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. Instead of employing a service provider to take control of a halfway-completed job, it is better to take into consideration using one prior to you start. Opportunities are you may need a professional plumber to make tube links.
This post will help you install a brand-new bath tub in your bathroom if you have currently gotten a new tub and also don't require to transform the setup of your previous water system pipelines.
Your tools and also product list must consist of the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installment


    To start with, the supporting structure supplied with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to prevent pressure on the tub.
    Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you make use of every one of the provided washing machines.
    Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last placement.

    Removing Old Taps


    If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the water system. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic because of the limited accessibility that is often the instance.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
    Prior to proceeding to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

    Mounting the Bathtub


    Using the two wooden boards under its feet, put the bath tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 little points.
    The next goal is to make sure that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub up until the level reviews level.
    To mount faucets, fit all-time low of the outermost flexible faucet port to the proper supply pipe by making a compression sign up with; then do the very same for the various other faucet.
    Activate the water system as well as check all joints as well as new pipework for leakages and tighten them if needed. Fill the bath tub as well as also inspect the overflow electrical outlet and the regular outlet for leakages.
    Ultimately, repair the bath paneling as explained in the maker's user's manual. Tiling and securing around the bathtub ought to wait up until the bath tub has actually been made use of at least when as this will certainly resolve it right into its last position.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end gives a link to the existing supply pipes.
    If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
    Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in area in between the tap as well as the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the location where the bath meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to split a rigid seal, creating the water to penetrate the wall surface in between the bathroom and also the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling listed below.
    You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bathtub with water prior to securing, to enable the activity experienced when the tub remains in use. The sealer can crack rather early if you do not think about this motion prior to sealing.
    Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant glue and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    We had been shown that editorial on How to Install a Bathtub Yourself from someone on our other blog. Enjoyed reading our piece of writing? Please share it. Let somebody else find it. We appreciate reading our article about Installing A Bathtub.


    Urgent plumbing needs? Seek professionals.

    Report this page